KMW –Long Range Solutions
Little things matter at a distance. . . .
Our Signature Custom
Combat Stock is designed by
Stocks. It was developed over a
period of 6 years and includes input from top
competition shooters as well as law enforcement
agencies across the
This stock features an ambidextrous thumbhole grip and
cheek piece design. Unique features include a very low profile forend
with a conformal bottom custom molded for the excellent Harris S-Series bipods.
Marble and camouflage patterns are molded into the Gel
Coat outer layer.
adjustable cheek piece hardware. This
designed hardware is proven to retain shooter
preferences when removed and replaced and will not vibrate loose when shooting or
transporting the rifle.
The stock includes 5 flush mounted sling hard points and a convertible
bipod station on the forend that allows use of Harris type bipod or
Picatinny mounting bipods. All SENTINELs have KMW- L.O.P. Spacer System and Pachmayr
The stock is fitted with detachable magazine bottom
hardware and accepts Accuracy International 10rd A.W. magazines as well
as 5 and 10 round A.I.C.S. magazines. See below
for more info about this dedicated DBM system.
Length of Pull
is adjustable from 12.7" to 14.3"
weight is 5 lbs, 2 oz.
curves, grips and lines are symmetrical from side to
side. Stock is designed to be easily shot from
left or right shoulder.
The firing grip area utilizes a new generation
thumbhole design that is meant to offer the user a
control surface that is comfortable from all
positions and for prolonged periods of use.
The trigger reach and position in relation to the
grip is designed to accommodate a wide range of
users. Hand position and access to bolt,
trigger and magazine release is meant to be
intuitive for the user. There is molded in
surface texture in this area to offer a more slip
Ultra Low Profile Forend:
. . positions the barrel into a very low center of
gravity in relation to the rest of the stock and any
bipod or rest. This configuration helps
minimize rifle twist generated from the torque of
bullet spin up and helps reduce perceived muzzle
There is molded in surface texture on
each side of the rear forend area to offer a more
slip resistant surface when in using a conventional
two handed grip.
Conformal Bipod Station:
The bottom, front of the forend has an integrally
molded-in station dedicated to the excellent Harris
S-Series bipods. This feature places the apex
of the bipod legs as close to possible to the bore
This molded-in station controls and
locks the bipod body preventing the skew or twisting
experienced when these or other bipods are attached
to conventional stocks with large flat bottoms.
Cheekpiece: Many modern rifle
systems are configured with a day sight or scope/night vision combo that places the sight plane
higher above the bore line than conventional hunting/target rifles. This has evolved the need to
place the shooter's cheek position higher so that
the optic can be viewed comfortably and consistently
for extended periods. The
COMBAT STOCK meets this need with an integral
adjustable cheek piece molded separately from the
main stock for enhanced strength and adjustability.
The heart of this stocks Integral Adjustable Cheek piece is the
This hardware is was designed and developed by
to specifically survive the rigors of duty and
service use without vibrating loose.
Adjustable for vertical as well as lateral user
preferences, this hardware will retain the user
settings while removing and re-installing the cheek
piece during routine maintenance.
Heavy Duty TG/DM:
This stock utilizes a trigger guard and integrated detachable magazine
system developed by
to maximize ease of use and reliability. This
stock was designed to allow the trigger guard to be
merged precisely into a well refined system.
Our bottom metal accepts Accuracy International AICS
believe we have developed an exceptional magazine
release that is easier to use, more damage
resistant, and more snag resistant than any other
bolt action DM system in existence. This
magazine release offers all of this while still
being accessible with gloves on and while minimizing
the chance of accidental magazine loss.
of the trigger guard are recessed to allow maximum access to the
magazine release while still protecting this part from damage.
This feature also helps reduce the chance of accidental release of the
magazine during aggressive or rough handling of the weapon.
system includes a funneled magazine well that offers
greatly improved insertion of the magazine into the
weapon compared to other systems currently on the
market. This stock
and DBM system offers maximum vertical support of the
magazine for reliable and repeatable positioning of
the rounds in relation to the receiver's feed ramp.
All inside and
outside edges of this unit are radiused so that there are no sharp
edges. All surfaces and corners are much more user friendly than
most DBM systems on the market. Production costs are increased to
include this feature but the final design and finished product are
superior to anything else in current production.
access holes in this DBM system feature internal snap rings that allow
access with the hex drive wrench but prevents loss of the bolts should
the stock be removed from the rifle.
STOCK AND D.M. ASSEMBLY MATCHED
Wide Area Recoil Pad:
All cross sections of the
COMBAT STOCK are
kept lean. This stock is thick where it needs
to be yet slim in areas that allow it with no loss
of strength or user comfort. The rear of the
stock butt sports a slim cross section that flares
to an increased size behind the adjustable cheek
piece. This is to allow the maximum reasonable
width and height recoil pad. Not to be
confused with the recoil pad THICKNESS, a wider and
taller pad increases the total square inches in
contact with the users shoulder. The more
surface contact that exists between the rifle and
shooter, the better the recoil forces are
distributed. A fixed recoil force distributed
over more area equals less pressure per square inch,
which equals decreased perception of recoil to the
comes with Length of Pull Spacer System installed. L.O.P.
adjustment range is from 12.7" to 14.3"
The weakest point of most conventional stocks is at
the cross sections where the recoil lug and magazine
feed system resides. The
this area with a reinforced midsection. The
width of this stock is approximately 0.100" more
than many of its counterparts. While allowing
more material margins around the action inlet, this
stock is still very much at home with standard size
1.350" diameter actions. The drop belly
midsection is designed to offer very comfortable
textured grip areas when used in positional firing
positions. The design goes to great lengths to
blend all lines and curves into an ergonomic package
that offers comfortable user contact surfaces.
Toe hook: The toe of this stock includes an
integrated grip area that can be used to anchor and
or steer the rifle with more control than
conventional stock butts. This section of the
stock is shaped to be used alone or in conjunction
with a rear pinch bag type rest. There is
molded in surface texture in this area to offer a
more slip resistant surface.
Camo Gel-Coat: This feature is unique to McMillan Fiberglass
Stock's manufacturing process. In
addition to being very strong and durable, this
Gel-Coat can include integrated colors literally
molded into the shell of the stock. Different
camouflage patterns and color themes can be
specified during the manufacture of each group of
CUSTOM ORDERING STOCKS
can custom order SENTINEL Combat Stocks for individual customers and
shops. Pricing is the same as stocks already in inventory.
In the past, I have not required a
deposit when placing custom orders but due to a surge in the number of
customers canceling orders just before delivery, I have had to implement
a new policy. 50% of the workorder is due when the custom order is
placed and the balance is due when the stock is ready to ship.
HOW TO PROCEED WITH ORDERING: You
can email me the details of your stock order via the address on the home
page of this site or with this link
I will need to know the colors and pattern type you want molded into the
stock. I will need to know the action type, barrel contour and
recoil lug type you want to accommodate. I will also need to know
if you require any upgrades such as the I.M.B., MUNSter N.V. mount,
extra flush cup hardpoints or extra magazines. I would also need
the name, address and phone contact info as you want it to show on your
invoice. Stocks can be shipped direct to you or to the shop of
By default, this stock will come with KMW
adjustable Length of Pull spacer system and KMW LoggerHeadTM
adjustable cheekpiece hardware installed. All stocks will come
with 5 flush cup hardpoints: 3 on the support side and 2 on the
strong/bolt side. Unless otherwise directed, I will default the
barrel channel to a Heavy Varmint contour which will easily accommodate
most future barrels you may use.
Upon receipt of your information, I will
enter your specifications into a workorder for you to review. The
workorder would be edited and questions answered until it reflects what
you desire. Upon your approval, a Purchase Order will be issued to
McMillan Fiberglass Stocks specifically for your stock and the P.O. will
be slaved to your workorder. You will be CC'd the email with P.O.
attached when it is sent to McMillan. This way you have a record
of the order entry and will not be wondering if the order was placed 2
In order for McMillan to stay efficient
and concentrate on producing our stocks, I request that you not
contact McMillan for status, changes or cancellations of any of my
orders. Contact me via the same email above or call my shop and I
will be glad to help.
Delivery time for a complete stock
package is largely dependent upon the cycle time at McMillan. This
will vary with their work load. Once I receive the raw stock from
McMillan, we try to install all necessary hardware and clean up the
stock for shipment within 2 weeks.
I am currently quoting 5 months on
Click on the photo for more information. . . .
matter at a distance . . . . .
© 2007 by KMW. All
Page Optimized for
Internet Explorer 7.0 or Newer
Last revision 10/19/2011